Real wood is still the homeowner’s favorite choice of flooring and caring for it takes minimal effort. Unlike laminate or engineered wood, hardwood is often refinished many times, and will add years of beauty and warmth to your home, as well as increase its value and speed its resale. Prolonged floor care is needed to keep your hardwood looking its best, however , and there are four major aspects of toronto hardwood flooring care:

  • 1 . Wooden floor cleaning
  • 2 . Hardwood floor repair
  • 3. Hardwood floor refinishing
  • 4. Hardwood floor protection

Clean Your Hardwood Repeatedly

Knowing how to clean hardwood floors is important because the bane of hardwood is dirt and grit, which will scratch and mark the ground if not removed promptly. As well, dust is seen more easily on wood floors than it is on linoleum or on carpet, especially in the sunlight and especially if the floor has a dark stain. Hardwood floor care, therefore , means sweeping and dusting regularly – once a week or so, at least, and after any event that leaves dirt and grit behind. Regular household dusting and cleaning products will cause problems, however , and you must use only products specifically designed for hardwood. Vacuuming is preferable to sweeping because it allows the dirt and dust to be plucked from between the boards, but use a vacuum with a bare floor attachment, not a beater bar, which can damage the wood.

Any time a more in-depth cleaning is required, use a cleaning method appropriate to the finish on your floor. If your floor has a glossy finish, it means of which polyurethane, or a water-based urethane, or a similar finish has been used to form a protective barrier over the hardwood. If it has a matte finish, it means that the floor is protected with a penetrating seal of oil and/or wax. On neither of these finishes can be water an acceptable cleaning agent, but both of them can accept a surface, damp-mop cleaning, which means the mop is not wet nonetheless only damp to the touch. You are cleaning only the surface and not using enough water to penetrate even the oiled-and-waxed hardwood. When using a moist mop on oil and waxed hardwood, you can add a little neutral ph hardwood floor cleaner to the water before dipping the exact mop into it. A floor with a protective glossy barrier can accept a generic hardwood floor cleaner providing it doesn’t contain any sort of wax or oil.

The don’ts are every bit as important as the do’s in hardwood floor care;

  • 1 . Don’t use ammonia, usual floor cleaners, household cleaners, or dusting products on hardwood.
  • 2 . Never use wax on a floor with a urethane or simply other glossy finish.
  • 3. Never wash hardwood; use only a slightly damp mop.

Repair Any Damage to Your Floors as Soon as Possible

Usually, when your oil and waxed hardwood floors have suffered surface damage, you have to remove the finish with a wax or oil lap dancer before dealing with the damage. After completing the repair, you then re-wax or re-oil the area. Surface damage occurs less often on wood floor protected by polyurethane or a similar type of sealer, and when it does, the damage is not as obvious. When repairing floors with like finishes, strip the finish from the entire board or boards where the damage has occurred. Make your repairs and then apply a ending product to those boards that is consistent with the rest of the floor.

1 . Water marks: Remove the protective finish, rub the marks with very good grade steel wool. Repeat if necessary, clean, and then refinish.

2 . Burn marks: Lightly sand the area, use a damp cloth to add the grit, and then refinish as desired.

3. Scratches and gouges: Conceal shallow scratches with matching wood putty or simply a putty stick. After the area is dry, sand and refinish.

Refinishing Your Worn Hardwood Floors Will Recapture Their Primary Beauty and Value

In a home with shabby hardwood floors, the biggest improvement you can make is to refinish the floors. Begin by building any necessary repairs, and then removing all the furniture and drapes and sealing the vents and registers in the room so that you will not likely spread dust throughout the house. Sanding floors is easiest to do with a drum sander and an edging machine for the sides plus corners of the room. You can rent these machines, and it is a good idea to rent a buffer or floor polisher at the same time. Plan to generate three passes with your sanding equipment, using increasingly finer sandpaper each time. Vacuum carefully and pick up every bit of fine dust particles and grit with tacking cloths. All dust and dirt must be removed. You can now apply a stain if you wish or you can give the natural color and design of the wood – such as the popular oak, maple, or cherry – to be displayed.

Improve and clean the dust and dirt from the floor again, and then apply your sealer – a polyurethane or a water-based urethane material that provides a protective barrier, or oil and wax, which penetrates the wood and protects from within. Carefully read the information accompanying each product, follow the safety advice, and apply as many coats of stain or sealer as suggested by the vendor of the products you are using.